如何做個支撐架？

ValleyViews

做個焊接件支撐架，并做個簡單的有限元分析試驗。

第一步：建新文件，使用公制長度單位。
" o- Q# L! P& P: j" b$ T& w
& j' D7 `/ Q- f/ {: u2 w: e% u
  c+ m( ]+ W; G6 J. i$ K2 H第二步：創建一個矩形。
5 x- z, X! X, W
5 l% H  h, F9 {- ?
第三步：先垂直約束至中心。
& t& f7 D* Y* {6 _/ i3 x8 y6 ]
1 K, g) W: L. w0 U& c' F
第四步：再水平約束至中心。然后結束草圖。

ValleyViews

第五步：矩形板厚度設定為10mm 。


第六步：選擇上平面做草圖。

ValleyViews

第七步：草圖上定位四個點。可使用垂直水平約束。

. ^* k0 C( R+ A0 c( q" R7 d/ k: Q3 B
( h) |3 W( k0 R1 h第八步：加尺寸，完成草圖。

ValleyViews

, G' f. Z& F+ y, V2 w5 k
9 E) k, J; w+ k) c2 c1 d第九步：We use the hole command and a new window appears. Our points should be autoselected for hole centers. If not select them manually. In the window we choose 14mm for our holes diameter and through all for termination. Then we click OK.


第十步：Finally we will add properties to our part. In the model browser right click Part one and in the menu choose iProperties.

ValleyViews

# C8 }0 N" \) I' T; Z第十一：Go to Physical tab and in the Material drop down menu choose Steel Mild. We will need those properties for our FEA test. Once you are finished save your part.
% r- v3 \4 W. g/ H+ |' ~
: t9 \& x! n) m; }2 f" R
$ _6 t7 w% G4 ~2 ~6 r第十二：Create a new part with the dimension shown in the image using the exact same steps as above. The holes should be in the center of the part. Add properties and save.

ValleyViews

Step 13: Create a new part with the dimension shown in the image using the exact same steps as above. Add properties and save.

! e$ \/ l$ b. ~2 ?$ k
$ M7 u& Q6 ^: {8 s9 `) _8 p, v0 vStep 14: Choose new and choose Weldment (ISO).iam

ValleyViews

Step 15: In the Assemble tab choose place component. In the new window browse to the location we saved our first part, select it and place it. By deafault the first part that is placed in an assembly or weldment file is grounded. You can change that later but for this tutorial we will keep this configuration.


* v( Q5 V) ~3 A3 _  jStep 16: Do the same for the second part.

ValleyViews

Step 17: Using the constraint command and selecting Mate we choose the faces of our parts shown in the red arrows. then select Apply.
5 I$ P( E; R/ \: U

Step 18: This is what we should be looking at if everything was done correct.

ValleyViews

Step 19: Then choose flush instead of mate (red circle) and select the two faces shown. In the Offset value (red circle) put 40mm offset. Click Apply.

  V$ Q* G% o3 |7 @
% g. k9 [; j% QStep 20: Expand Part1 and Part 2 in the model browser. With the flush command still active choose the YZ plane of part 1 and YZ plane of part 2. Click OK.

ValleyViews

Step 21: This is what we should be looking at. Now Part 2 is fully constraint.


: M! }) ^: Q$ F3 e/ o! Q; A7 `' lStep 22: Next we place our third part 2 times. Use the exact same steps for placing part 2.